Introduction to Mordanting Cotton
Now that you have scoured your cotton, you are ready to start mordanting it.
It is very important to work the fibres in the pot with gloved hands but check that the water is not too hot for your hands first. Squeeze the fabric inside the pot with your hands, then unfold the fabric a few times, making sure the mordants penetrate in every nook and cranny. If you just plonk your fabric in the saucepan and leave it there you will get a mottled effect when you dye (which may be just what you want).
Use no more than 100 grams of fibre in a ten litre saucepan. By fibre, I mean fabric, yarn, or cotton sliver from a specialist shop. If you use more than 10 grams of fibre per litre, you will find it difficult to stir the fibre in the dye pot, and the mordant will not penetrate so well. A ten litre saucepan is quite heavy to lift, and I would not want to use a pot any larger than that.
You now need to choose which of the following methods to use for mordanting: a) & b) aluminium acetate
(which is a very fine powder), c) alum & tannin using the three-step alum-tannin process
or d) the new titanium oxalate process
a) Mordanting cotton with aluminium acetate: basic method (this page)
The basic aluminium acetate method is quicker, as you only need to make one mordant bath which means you will also use less energy. Aluminium acetate is also cheaper, even though it costs more than alum, as you will be using only 7 to 10 grams of aluminium acetate instead of 50 grams of alum.
b) Mordanting cotton with aluminium acetate: advanced method (opens a new page)
For best results use the advanced aluminium acetate method, which requires a tannin treatment followed by aluminium acetate.
c) Mordanting cotton with the 3 step process
(opens a new page)
The 3 step tannin and alum method is a useful alternative, as alum is slightly safer chemical to use than aluminium acetate as it is not such a fine powder; also aluminium acetate is not so widely available.
d) Mordanting cotton with titanium oxalate
(opens a new page)
Titanium oxalate is an interesting mordant to use, as you will get different shades than if you had used alum or aluminium acetate.
After mordanting, you can either dry the cotton and store it for later use, or use it straight away. Either way, make sure you rinse the cotton well to remove any unfixed mordant before you dye.
a) Mordanting cotton with aluminium acetate: basic method (1 step)
Aluminium acetate is recommended by Liles for plant fibres. This method seems to yield deeper and clearer colours, as it uses no tannin which can slightly yellow the fibres. It also has the advantage of using only one ingredient and one mordant bath, being therefore both quicker and cheaper.
Note: aluminium acetate is a very fine powder, weigh it carefully and use a mask when weighing this and other fine powders.
You will need;
- 7 to 10 grams of aluminium acetate
- 100 grams of scoured cotton fabric or yarn
- Soak 100 grams of cotton fibres in warm water for at least two hours.
- Half fill the dye pot with hot tap water
- Dissolve the aluminium acetate in a small container with boiling water.
- Add the dissolved aluminium acetate to the dye pot and stir. There is no need for extra heat as the warmth from the hot tap water should be enough.
- Add the wet cotton and squeeze it a few times wearing gloves. If you are mordanting yarn, especially fine weaving yarn, work the fibre in the pot very carefully, otherwise the yarn will get tangled. Leave overnight. Wring well and dry. Liles recommends waiting until the vinegar smell has disappeared, which he says can take up to 4 days.
- When you are ready to dye, rinse the fibre carefully to remove any unattached mordant.
How to scour cotton
Mordanting cotton with advanced aluminium acetate 2-step process
Mordanting with the 3-step alum-tannin process
Top of Page